The fastest way to expose a fake IW376063 is the chronograph layout and the pusher hardware. The genuine IWC Aquatimer chronograph in this reference family runs calibre 79320, a reworked Valjoux 7750, and its pushers are screw-down with clean threads and a short, firm travel. Our top pick in the current replica market is a 1:1 build on a Swiss-pattern 7750 with a signed IWC-style rotor, threaded pushers and laser-deep caseback engraving. Every option below is judged on four criteria: dial furniture and lume, case and bezel mechanics, movement and winding feel, and serial and paperwork consistency. One warning before anything else: IWC uses the trailing digits of a reference to denote a specific dial and strap combination, so match a candidate against photography of the exact IW376063 variant rather than a generic Aquatimer.

read more

What Gives a Fake IW376063 Away Fastest

Three details decide most comparisons: sub-dial geometry, pusher construction and caseback engraving. Because the genuine watch is 7750-based, a replica that also uses a 7750 places running seconds at 9, chronograph hours at 6 and chronograph minutes at 12 exactly where they belong. Quartz fakes cannot. They frequently replace one counter with a 24-hour hand or crowd the sub-dials toward the centre, and that single error is easy to see at arm's length. Check the date aperture next, then the weight of the printing under the logo.

read more

Pros of a 7750-based replica

  • Sub-dial positions match the genuine 79320 architecture
  • Chronograph starts, stops and resets in the correct sequence
  • Case height stays close to the original instead of the flat profile of a quartz fake

Cons

  • Movement finishing is often claimed but not delivered
  • Date font and aperture placement drift between batches
  • Reset feels softer than a freshly serviced 79320

Dial, Hands and Lume

Genuine IWC dials use applied metal markers with crisp polished edges and lume applied level with the surround. On fakes, look for lume sitting proud of the frame, a slightly green cast under daylight, and hands with visible machining marks along the bevel. The text block is the other tell: letter spacing on the model line should be even, and the printing should sit sharp at 3x magnification rather than feathering into the dial.

more on this topic

Pros

  • Good builds use genuine-spec Super-LumiNova and colour-match the markers
  • Applied indices give correct shadow lines under angled light

Cons

  • Hands are usually the weakest part, with soft polishing on the chamfer
  • Printing looks correct at arm's length but blurs under a loupe

Best for: buyers who plan to wear the watch and rarely photograph it. If you inspect dials under magnification, this is where money shows.

related article

Case, Bezel and Crystal

Run the bezel through a full turn. It should index with even resistance and stop cleanly at each marker, with the triangle landing on 12 when seated. Fakes show slack at the first click, a wobble in the bezel plane, and a gasket that squeaks. On the crystal, genuine anti-reflective coating reads almost invisible head-on with a faint blue or purple flash at an angle; cheap coating looks milky or leaves the dial grey.

Pros

  • 316L steel cases carry close to original weight on top-tier builds
  • Sapphire with inner AR is standard on the better tiers

Cons

  • Crown threads feel grainy and cross-thread if forced
  • Bezel springs weaken within a year on mid-tier examples

Best for: daily wear. A watch that lives on a wrist needs a bezel and crown that survive repeated use, not just a good photograph.

Movement, Winding and Pushers

Many Aquatimer chronographs of this family close with a solid engraved caseback, so the movement is judged by feel rather than sight. Wind it twenty turns: a 7750 should feel smooth with a faint ratchet tick, and the rotor should spin freely without a rattle when the case is tilted. Screw the pushers down fully and check that the collar seats flush. Replicas often shorten the thread so the pusher stops a half turn early.

Pros

  • Clone 7750s are serviceable and parts are widely available
  • Timing stability is usually acceptable for everyday use

Cons

  • Rotor engraving is shallow and lacks the depth of the original
  • Blued screws are often painted rather than heat-treated

Engraving, Serials and Paperwork

Caseback engraving on the genuine watch cuts deep with crisp internal corners, and the reference and serial between the lugs are stamped, not lasered in a dotted font. Paperwork should match the serial, the reference and the date of sale. A seller who cannot photograph the caseback in daylight, or who sends stock images instead of the actual unit, is not worth the conversation.

Pros

  • Top-tier builds reproduce reference and serial placement accurately
  • Correct font weight is achievable at this price point

Cons

  • Serial repetition across units is common on low-tier stock
  • Boxes and cards are frequently mismatched to the watch

Quick Verification Checklist

  1. Confirm sub-dials sit at 9, 12 and 6 and all three work.
  2. Screw both pushers down and check the collar seats flush.
  3. Turn the bezel through a full rotation and listen for even clicks.
  4. Tilt the crystal toward a window and look for a faint colour flash, not a grey haze.
  5. Read the caseback engraving under a loupe for sharp internal corners.
  6. Compare the serial to the paperwork and to the reference between the lugs.

Tier 1: Budget Quartz Builds

Cheap, thin and immediately wrong to anyone who knows the reference. The sub-dial layout is the giveaway and no amount of strap swapping hides it.

Pros

  • Low cost
  • Light on the wrist

Cons

  • Wrong chronograph architecture
  • Case profile too thin
  • Bezel action is loose

Skip this tier if you want the watch to pass any real inspection.

Tier 2: Standard 7750 Builds

The middle of the market. Movement architecture is right, finishing and dial work are not. This tier suits buyers who want the correct proportions and a working chronograph without paying for hand finishing.

Pros

  • Correct sub-dial positions
  • Serviceable movement
  • Reasonable case weight

Cons

  • Soft hand polishing
  • Shallow engraving
  • Inconsistent lume colour

Recommended for casual wear, weekend use and anyone buying a first chronograph replica.

Tier 3: 1:1 Decorated 7750 Builds

The closest match available. Signed rotor, correct pusher threads, deep engraving and dial printing that holds up under a loupe. This is the tier to choose if the watch will be handled by other enthusiasts.

Pros

  • Dial and case detail close to reference photography
  • Bezel and crown built to survive daily use
  • Engraving depth matches the original

Cons

  • Highest price in the replica range
  • Supply is limited and waitlists are common

Best for: collectors who want a display piece and understand that no replica is a genuine watch.

Legal and Resale Reality

In the United States, trafficking in counterfeit goods is prohibited under 18 U.S.C. 2320, and passing a replica off as genuine is fraud in every jurisdiction. Customs can seize counterfeit imports. Resale value on any replica is close to zero regardless of tier, so treat the purchase as a wearing cost, not an investment, and never represent the watch as an original.